收藏本站
LTM4601/LTM4601-1
APPLICATIONS INFORMATION
V OUT(MARGIN) =
? V OUT
R PGM =
V OUT 1.18V
The typical LTM4601 application circuit is shown in Fig-
ure 18. External component selection is primarily deter-
mined by the maximum load current and output voltage.
Refer to Table 2 for specific external capacitor requirements
for a particular application.
V IN to V OUT Step-Down Ratios
There are restrictions in the maximum V IN to V OUT step
down ratio that can be achieved for a given input voltage.
These constraints are shown in the Typical Performance
Characteristics curves labeled V IN to V OUT Step-Down
Ratio. Note that additional thermal derating may apply. See
the Thermal Considerations and Output Current Derating
section of this data sheet.
Output Voltage Programming and Margining
The PWM controller has an internal 0.6V reference voltage.
As shown in the Block Diagram, a 1M and a 60.4k 0.5%
internal feedback resistor connects V OUT and V FB pins
together. The V OUT_LCL pin is connected between the 1M
and the 60.4k resistor. The 1M resistor is used to protect
against an output overvoltage condition if the V OUT_LCL
pin is not connected to the output, or if the remote sense
amplifier output is not connected to V OUT_LCL . In these
cases, the output voltage will default to 0.6V. Adding a
resistor R SET from the V FB pin to SGND pin programs
the output voltage:
The MPGM pin programs a current that when multiplied
by an internal 10k resistor sets up the 0.6V reference ±
offset for margining. A 1.18V reference divided by the
RPGM resistor on the MPGM pin programs the current.
Calculate V OUT(MARGIN) :
%V OUT
100
where %V OUT is the percentage of V OUT you want to
margin, and V OUT(MARGIN) is the margin quantity in volts:
? ? 10k
0.6V V OUT(MARGIN)
where R PGM is the resistor value to place on the MPGM
pin to ground.
The margining voltage, V OUT(MARGIN) , will be added or
subtracted from the nominal output voltage as determined
by the state of the MARG0 and MARG1 pins. See the truth
table below:
MARG1 MARG0 MODE
LOW LOW NO MARGIN
LOW HIGH MARGIN UP
HIGH LOW MARGIN DOWN
HIGH HIGH NO MARGIN
Input Capacitors
V OUT = 0.6V ?
R SET
(k W )
V OUT
(V)
60.4k + R SET
R SET
Table 1 . R SET Standard 1% Resistor Values vs V OUT
Open 60.4 40.2 30.1 25.5 19.1
0.6 1.2 1.5 1.8 2 2.5
13.3
3.3
8.25
5
LTM4601 module should be connected to a low AC imped-
ance DC source. Input capacitors are required to be placed
adjacent to the module. In Figure 18, the 10μF ceramic input
capacitors are selected for their ability to handle the large
RMS current into the converter. An input bulk capacitor
of 100μF is optional. This 100μF capacitor is only needed
if the input source impedance is compromised by long
inductive leads or traces.
For more information www.linear.com/LTM4601
4601fd
11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LTM4602IV#PBF IC DC/DC UMODULE 6A 104-LGA
LTM4603HVEV#PBF IC DC/DC UMODULE 6A 118-LGA
LTM4603IV#PBF IC DC/DC UMODULE 6A 118-LGA
LTM4604AIV#PBF IC UMODULE DC/DC LV 4A 66-LGA
LTM4604IV#PBF IC DC/DC UMODULE 4A 66-LGA
LTM4605EV#PBF IC DC/DC UMODULE 5A 141-LGA
LTM4606MPV#PBF IC DC/DC UMODULE 6A 133-LGA
LTM4607IV#PBF IC BUCK/BOOST SYNC ADJ 5A 141LGA
相关代理商/技术参数
LTM4601AV 制造商:LINER 制造商全称:Linear Technology 功能描述:12A DC/DC μModules with PLL, Output Tracking and Margining
LTM4601AV-1 制造商:LINER 制造商全称:Linear Technology 功能描述:12A DC/DC μModules with PLL, Output Tracking and Margining
LTM4601EV#PBF 功能描述:IC DC/DC UMODULE 12A 118-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*
LTM4601EV#PBF 制造商:Linear Technology 功能描述:DC/DC ?Module IC 制造商:Linear Technology 功能描述:IC, STEP-DOWN DC/DC MODULE, LGA-118
LTM4601EV-1#PBF 功能描述:IC DC/DC UMODULE 12A 118-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*
LTM4601EV-1#PBF 制造商:Linear Technology 功能描述:DC/DC Converter IC
LTM4601EV-1PBF 制造商:Linear Technology 功能描述:DC to DC Power Supply
LTM4601EV-1-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:12A DC/DC ??Modules with PLL, Output Tracking and Margining